Extend past the roofline
Adjust the bracket from 9.4 to 14.5 inches to move the dish farther from walls, eaves, and roof edges.
Starlink Gen 3 Eave Wall Mount Adjustable Angle Bracket
Starlink Gen 3 Eave Wall Mount Adjustable Angle Bracket
SKU:XL0173
Regular price
$87.00
Sale price
$87.00
Regular price
$99.00
Unit price
per
Adjustable eave and wall mount for Starlink Gen 3
Move your Gen 3 dish higher, farther from the wall, and away from roofline obstruction.
This adjustable eave wall bracket helps position Starlink Gen 3 around roof edges, exterior walls, cabins, garages, and workshops where height, extension, angle, and cleaner cable routing matter.
For Starlink Gen 39.4-14.5 in extension15.9-25.2 in height90-180 degree angle
Check compatibility ->
Raise the dish position
Height adjusts from 15.9 to 25.2 inches so the dish can sit higher around roofline obstructions.
Cleaner cable route
Built-in cable management helps guide the cable through the bracket path for a neater outdoor install.
Fit check
Designed for Starlink Gen 3 Standard dish installation on exterior walls and eaves.
- Made for Starlink Gen 3 Standard dish wall and roofline installation.
- Extension adjusts from 9.4 to 14.5 inches to move the dish away from the wall or roof edge.
- Height adjusts from 15.9 to 25.2 inches for more flexible eave positioning.
- 90-180 degree angle adjustment helps fine-tune the dish position for open-sky visibility.
- Built-in cable routing helps reduce exposed cable clutter and outdoor wear.
- Best for suitable exterior walls, eave supports, garages, cabins, workshops, and remote homes.
Install only on a strong structural surface. Use proper fasteners for your wall material and consult a qualified installer if you are unsure about wall strength, roofline clearance, or local requirements.
Installation flow
Choose the surface first, then adjust the extension, height, and angle.
Roof edges, eaves, and nearby structures can block part of the sky view. This bracket gives you more room to tune the dish position before final tightening.
Pick a strong wall or eave point
Choose a structural mounting area with enough support and safe access for installation.
Set extension and height
Move the dish away from roofline interference and raise it to a cleaner outdoor position.
Route the cable cleanly
Use the cable path to reduce exposed wiring, sharp bends, and weather stress.
Key details
For Gen 3 homes, cabins, garages, and exterior wall installations.
Product typeAdjustable eave wall mount bracket
CompatibilityStarlink Gen 3 Standard dish
Extension range9.4-14.5 in
Height range15.9-25.2 in
Angle range90-180 degree adjustment
Cable designBuilt-in cable management path
Best forEaves, exterior walls, cabins, garages, workshops
Best use cases
Use it when roofline obstruction or messy cable routing is the problem.
Eave installationPlace the dish near the roof edge while extending it outward for a cleaner sky view.
Exterior wall mountingUse a wall-mounted position when roof mounting is not preferred or not practical.
Cabins and remote homesCreate a more stable outdoor Gen 3 setup around rural homes, garages, workshops, and off-grid buildings.
Complete the Gen 3 wall setup
Strongly related add-ons for cable reach, connector protection, and indoor organization.
Cable reach
Replacement Extension Cable for Gen 3/Mini
Add reach when the best eave or wall position is farther from the router or cable entry point.
View product
Cable protection
Waterproof Silicone Cable End Caps
Protect unused cable ends during wall routing, storage, or future maintenance.
View product
Indoor organization
Gen 3 Router and Power Supply Mount
Keep the indoor router and power supply area cleaner after the cable enters the building.
View productImportant notes
- Confirm your Starlink model before purchase. This bracket is intended for Starlink Gen 3 Standard dish installation.
- This product includes the eave wall mount bracket kit only. Starlink dish, router, cable, power supply, extension cable, cable caps, and indoor mount are not included unless purchased separately.
- Install on a strong exterior wall, eave support, or structural surface that can safely support the bracket and dish.
- Use proper fasteners for your wall material and check local installation requirements before drilling.
- For elevated installs, use proper fall protection or hire a qualified installer.
FAQ
Starlink Gen 3 eave wall mount questions
Is this mount compatible with Starlink Gen 3?
Yes. It is designed for Starlink Gen 3 Standard dish installation.
Can it reduce roof obstruction?
Yes. The adjustable height and extension help move the dish farther from the roofline for a clearer sky view.
What is the adjustable range?
The extension adjusts from 9.4 to 14.5 inches, and the height adjusts from 15.9 to 25.2 inches.
What angle range does it support?
It supports 90-180 degree angle adjustment for more flexible dish positioning.
Does it help with cable management?
Yes. It includes built-in cable routing to keep the cable cleaner and better protected from outdoor exposure.
What should I pair with this bracket?
A Gen 3/Mini extension cable, waterproof cable end caps, and an indoor Gen 3 router/power supply mount are strong related add-ons.
